Denver · what it costs
The repair bill against a new dual fuel range
The one page here that prints what a new machine costs, because a comparison is only worth reading when both halves of it are on the table.
This job lands between $180 to $910 parts and labour, agreed before anything comes apart
Even the dearest two bands on this range, arriving in the same year, land a long way below a new one — which is why a second fault is rarely the moment to give up on equipment designed to be taken apart. Wolf Pro Repair Denver puts the whole ladder in front of you before you decide: (720) 649-6641.
The figures
What the bands say about this one
| The work | Where it turns up | Parts and labour |
|---|---|---|
| Igniter or spark module | the gas half of a dual fuel range, when a burner ticks and ticks before it catches | $180 to $470 |
| Burner valve or orifice service | a simmer that will not sit low, or a flame that has never been matched to this elevation | $240 to $560 |
| Oven thermostat or sensor calibration | a cavity that bakes to the wrong number however long you give it | $210 to $460 |
| Convection fan or motor | a fan that howls, rattles or falls silent while the cavity still heats | $300 to $650 |
| Door hinge, glass or seal | a door that sits proud, drops open, or lets heat out over the top | $270 to $700 |
| Control board or touch panel | a panel that has gone dark, frozen or deaf to the pads after a power cut | $470 to $910 |
What moves it
Four things decide where in that spread you land
-
How many bands are in play
One fault is a repair decision and nothing more. Three of these lines arriving together on the same range is a different conversation, and the only honest way to have it is with the figures written down.
-
Which half has gone quiet
Gas-side hardware sits at the bottom of the ladder. The electric cavity and the panel that drives it sit at the top, and a fault in one half says nothing at all about the other.
-
What goes in around a new one
The appliance price is where a replacement starts. The range still has to be levelled, engaged with its anti-tip bracket, wired at the terminal block and leak-checked at the gas connection.
-
What the opening will take
Range widths are fixed, and so is the clearance Wolf wants between the cooking surface and the hood above. A different size pulls cabinetry and ventilation into the job.
Adding the bands up honestly
Take the two dearest lines in the table, put them both in the same twelve months, and the total still sits well under the price of the machine they are fitted to. That arithmetic is what keeps professional ranges in kitchens: each part is replaceable on its own, the burners and the cavity are separate systems, and nothing in the list above condemns the rest of the appliance. The fault worth thinking twice about is not the expensive one — it is the one that keeps coming back to the same circuit after it has been put right.
What replacing actually involves
Replacement means buying a comparable professional range, before installation and ventilation work, which comes to $7,570 to $18,460 — and the gas connection, the terminal block, the anti-tip hardware and whatever the hood above needs all sit outside that. Wolf’s own cover also runs from the date the range was first installed, so a recently finished kitchen and one finished a decade ago are not in the same position — worth establishing before anybody decides anything. Tell us what the range has already had done to it when you ring, and the ladder can be read against this particular machine rather than against ranges in general.
Where this sits on the site
- The repair itself Range Repair
- Everything priced All 9 price pages
Reviews
What the bill looked like afterwards
Wolf cooking equipment, in and around Denver.
4.9 / 51,148 reviews
Touch panel went blank after a storm knocked our power out twice in a night. Not the board I expected, but a cooked ribbon connector behind the trim. Working since; the parts wait cost a star.
Rafferty O.Baker
The oven thumped when it lit, loud enough to make us jump. A weak igniter was letting gas build before the flame took. New igniter, and he checked the burner ports while he had it apart.
Hazel W.Baker
Heat was pouring out over the top of the door and the cabinet above had started to discolour. The seal had gone hard and shrunk, dry air here being what it is. A new gasket sorted it.
Weldon T.Hilltop
Denver · Wolf only
Get the band before the visit, not after
One call, one reading, one figure agreed in writing. Somebody picks up around the clock, and the booking page takes a slot at any hour of the night.
$89 for the visit, taken straight off the repair once you approve it.